Constitute a Classy Craft Picture Frame
The fastest custom to add cachet and sophistication to an oil illustration, a print or your own Craft is to packet it using a distinctive frame. A frame adds substance to your Craft, becomes a focal location when hung right, and attaches monetary worth to the quota. This article Testament break down lay a frame in sync and how bad to dash it. These directions assume you are purchasing ready-made and cut-to-size frame pieces.
Instructions
Framing Art: from Pieces to Wall
Make a mark. Here is where you will screw in the picture eyehooks or D-rings. If the wood is hard, you may need to make pilot holes to begin. Install the eyehooks or D-rings.
Constitute all your materials. Besides, gain a soft surface available to chore on, such as a abundance of latex foam or a padded surface---similar to a padded ironing board.
A print or a photograph Testament glad eye still higher quality matted. A mat besides keeps the Craft elsewhere from the glass or acrylic and prevents sticking. Mats longing to be incision by a know stuff with a mat-cutter effects; too, mats can in reality be bevel chop, adding another dimension to your Craft. Analysis with resident framers or hobby stores with framing departments.
2. Country the frame pieces on your exertion surface and build them into the licence configuration. Construct firm that the mitered corners limit up nicely, with no unsightly gaps.
Manipulate wood adhesive to the ends of Everyone adjoining quantity with a brush and bond the corners well-organized. Some professionally prepared frames gain slots chop into the back of the frame plenty and equip wood biscuits to district in the slots. If so, slide the biscuit into each corner---this helps to solidify the frame strength. You may need to use your picture frame clamp to hold them until dry. Make sure that the clamp is padded and not digging into the wood.
Using a damp rag, wipe off any of the wood glue that has oozed out. Allow the frame to dry overnight.
3. Remove the clamp.
If using glass, take your frame to a glazier, who will custom cut your glass. If you are cutting your own backboard, do that at the same time.
To start assembly, place the frame onto the soft surface, upside-down. Clean and insert the glass. Insert the mat. Test to see where the art will fall in the frame; affix the art to the mounting with masking tape (linen tape preferred). Insert the backboard.
4. Use panel pins to hold everything in place. Support the frame in a padded wood block or vise so it won't move around. Gently, hammer several panel pins into the inside edge of the frame, spaced evenly. Only sink the pins halfway; the protruding ends of the pins will hold the work in the frame.
5. Apply adhesive to the back of the frame all along the edge. Lay a piece of Kraft paper or a paper bag over the glue, covering the whole back. Wipe excess glue away and trim the paper to the frame edge with a craft knife. The artwork is now in the frame and the back is sealed to prevent dust, etc. from reaching the surface.
6. Measure one-third down from the top of the frame on the vertical pieces.1. Degree your Craft. Provided it is a principles proportions, For instance an 8 x 10-inch extended canvas, you can get inventory frame pieces and the backing board online, or at a hobby store such as Hobby Foyer or Michael's. Otherwise, you may duty moulding from a homely improvement store---ask them to chop it according to your measurements. Then cut a length of picture wire that equals the width of the frame plus 4 inches. Thread the picture wire through each hook or D-ring and across the back of the frame, protruding 2 inches on each side. Wind the excess over itself like a twist-tie at each end, and trim the wire if necessary.
7. Art should be relative in size to the wall or the furniture in front of it. Hang important art at eye level. If you are unsure of placement, the best thing to do is trace around the art on a Kraft paper or paper bag, then cut it out and move the template around until you are satisfied.
Professional artist Robert Terrell suggests hanging art at 57 inches center---that means 57 inches up from the floor to the center of the art.
