Shade printing can be used to print infant shirts.
Shade printing with emulsion is a hobby anyone can adoration, still whether they enjoy regional artistic know-how. You Testament be printing the artwork from your personal computer, so you can bonanza any dusky and ghastly figure to print on the transparency. For the cleanest prints, choose an drawing that is composed of lines such as a coal and immaculate cartoon. The "backside" of the Shade is the side contrary of the inner frame since this is the side which Testament be placed down on the framework or paper.
Instructions
Make a Screen for Printing
1. Chart your artwork on govern bleached paper using one shot jet ink. Inspect the effigy into your personal computer and print the angel onto transparency paper. Utilize the "transparency movie" or "speciality paper" setting in the print options.
2. Acquisition a windowless amplitude in the co-op, and bag onliest a copper lightbulb while working with emulsion. You are using photography chemicals which behave to Common luminosity, so it is influential not to expose the Shade to blaze until the emulsion operation is adequate. It is primary to wear gloves while you are working with emulsion chemicals thanks to they Testament burn your skin.
3. Alloy the emulsion Correct with the similar sensitizer according to manufacturer's instructions. Assign a hearty immensity of emulsion mix along the replica of the inside of the Shade with a spatula, domicile the squeegee at the backside of the Shade and clench the squeegee at a 45-degree angle facing the top of the Shade. Drag the squeegee up while urgent firmly into the Shade.
4. Keep at coating the screen with emulsion until the Shade is coated in a thin yet layer of emulsion. It is extensive to smooth any Rugged areas so your prints gander Disinfected and still. Coat the other side of the Shade with emulsion fluid in the same way while the other side is still wet.
5. Allow the emulsion to dry for two hours. Lay a piece of solid black cloth or a black board on a flat surface of the dark room. Place the screen on the black cloth with the bottom side down.
6. Place the printed transparency artwork on the screen. Lay the heavy glass on top of the transparency. Hang a light with the 250-watt bulb 1 to 1 1/2 feet from the screen and turn it on.
7. Let the emulsion expose in the light for 15 minutes. You can turn on ordinary lights now, but you have to work fast. Firmly spray out the screen to remove emulsion from the areas which were not exposed to light.
8. Be sure when you hold the screen up to the light, the negative image is not cloudy. If it is, continue spraying with cold water until all the emulsion is removed from these places. Fill in unwanted gaps or pinholes in the emulsion with more emulsion and allow to dry.
Make Prints
9. You can make multicolor prints with the same screen.
Tape a large piece of acetate firmly to the table so that the tape will act as a hinge while keeping acetate firmly in place. Lay your screen over the acetate to make your reference print. Hover the screen over the acetate so it is not touching and place a hearty line of ink on the screen a couple of inches above the design.
When the image is aligned, flip the acetate away from the screen on its hinges.12. Lower your screen onto the fabric or paper. Lift the screen to hover it above the surface and immediately recoat the screen with an even layer of ink as before.
11. Lift the screen to an upright position on the hinges and place the item to be printed under the acetate. Use the print on the acetate to align the image on the fabric or paper.10. Lightly drag the squeegee down the screen to spread the ink in an even layer across the screen. Lower the screen down onto the acetate and firmly drag the squeegee up the screen at a 45-degree angle facing up.
Firmly and smoothly drag the squeegee across the screen to transfer the image. Lift the screen and allow your new print to dry in a safe place.
13. Now drag the squeegee in the opposite direction, holding the squeegee at a 45-degree angle pointed in the direction you will be dragging it to. Press firmly with the squeegee this time to ensure the fabric or paper underneath receives an even film of ink.
